Skip to content

Door Installation and Repair in London, Ontario

Home entry with a wooden front door and staircase

What Door Installation and Repair includes

  • Interior door hanging and trimming
  • Exterior door and weatherstripping repair
  • Lock, latch and strike-plate adjustment
  • Frame repair and re-casing

How we work

  1. Preparation. Tell us about the job. We review photos and details, ask the right questions and give you a clear estimate.
  2. Communication. We agree scope, materials and timing with you and keep you updated as work progresses.
  3. Execution. We do the work carefully, protect your space, clean up and walk you through the result.

Good to know: Drafty exterior doors often need new weatherstripping or a threshold adjustment, not a full replacement.

A door is used more than almost anything in the house

Every day, doors open and close, lock and unlock and hold out the weather. When they work, nobody thinks about them. When they do not, everyone does: the bedroom door that will not latch, the front door that lets in a draft, the closet door that rubs, the patio door that sticks in summer. Doors also matter for safety and security, and a poorly fitted exterior door affects heating costs and comfort.

This guide explains how door installation and repair works in London, Ontario homes. For the problems that interior doors most often have, see our blog guide on sticking, sagging and misaligned doors.

Door installation: hammer, tape measure and tools laid out on a wooden cabinet
Many door problems are fixed with hinge adjustments and basic hand tools.

What we do

  • Interior door installation. Prehung and slab doors hung, trimmed and adjusted.
  • Exterior door repair and weatherstripping. Drafts, thresholds and seals.
  • Sticking and sagging doors. Hinge repair, frame adjustment and planing where needed.
  • Locks, latches and strike plates. Installation, replacement and adjustment.
  • Frame repair and re-casing. Damaged jambs and casings repaired or rebuilt.
  • Closet, pocket and bi-fold doors. Track, roller and alignment repairs.
  • Hardware. Handles, hinges, door stops and closers.

Interior doors: installation

There are two main types of door.

  • Prehung doors come already mounted in a frame with hinges attached. They are easier to install square and plumb, and are the usual choice for new openings and replacements.
  • Slab doors are just the door. They are used when the existing frame is in good condition. The hinge and latch locations must be cut to match.

The process generally includes:

  1. Measure the opening, including height, width, wall thickness and swing direction.
  2. Prepare the opening, checking that the frame is plumb, level and square.
  3. Set and shim the frame so it sits true, then fasten it.
  4. Check the gaps, aiming for an even reveal around the door.
  5. Install hardware: handle, latch and strike plate.
  6. Install trim, fill, caulk and finish.

Interior doors come as hollow-core, which are light and economical, and solid-core, which are heavier and quieter. Consider sound, weight, style and the hinges when choosing.

Exterior doors: drafts, security and weather

Exterior doors face rain, snow, sun and wide temperature swings. They also need to be secure. Common issues include:

  • Worn weatherstripping. Compressed, cracked or missing seals let air and water in.
  • Threshold problems. A threshold set too high or low leaves gaps or drags the door.
  • Door shifting. Movement in the frame changes the gaps and the latch alignment.
  • Light visible around the frame. A sign of gaps that need sealing.
  • Damaged or rotten frames. Moisture at the bottom of the frame is common.

Many drafty doors can be fixed with new weatherstripping, an adjusted threshold and caulking, which is far cheaper than replacing the door. If the door or frame is badly damaged, replacement may be the better answer, and we tell you honestly which is which.

Locks, latches and security

A lock is only as good as the door and frame around it. A deadbolt in a weak frame can fail, so we check the strike plate, the screws that hold it and the frame. Longer screws that reach the framing strengthen the whole assembly. We install and replace handles, locks and deadbolts, and adjust latches that do not catch. If you want a particular lock or smart lock, tell us the model, and we confirm that it fits.

Sticking, sagging and rubbing doors

The fixes follow a clear order, from simple to permanent:

  1. Tighten loose hinge screws, and replace them with longer ones where needed.
  2. Check the gaps to see where the door rubs.
  3. Adjust hinges and shims, or the frame.
  4. Sand or plane only as a last resort, and seal the cut edge.

Humidity changes cause seasonal sticking, so we consider the time of year before removing wood.

Carpenter working at a bench in a well-equipped woodworking shop
Frames, casings and trim are repaired and finished to match.

Frames, casings and trim

The door frame and trim hold everything together. Damaged jambs, split casings and loose trim can be repaired or replaced, and new trim is matched where possible. See carpentry for related work. If the door height changes after new flooring is installed, doors may need trimming. See flooring services.

Closet, pocket and bi-fold doors

These doors rely on tracks, rollers and guides, which wear and shift. Common fixes include re-hanging a door on its track, replacing rollers, straightening a bent track and adjusting the pivots. Pocket doors that stick or come off the track often need access to the frame, and we tell you what is involved.

Condos, rentals and commercial doors

Building rules may affect the doors you can change, especially entry doors with fire ratings. Check with your property manager before replacing or modifying a rated door. For rentals and businesses, we can repair doors between tenants or outside business hours, and tell you where a door falls outside what we can change.

Common door mistakes

  1. Planing before checking the hinges. Wood removed cannot be replaced.
  2. Replacing a door that only needs weatherstripping. A costly fix for a small issue.
  3. Short hinge screws. They hold only the jamb, not the framing.
  4. Ignoring the frame. A new door in a crooked frame will not work.
  5. Not sealing cut edges. Moisture gets in and the door swells.
  6. Weak strike plates. They compromise security.
  7. Measuring wrong. The wrong door size or swing wastes time and money.

How to prepare

  • List of doors with problems, with photos.
  • Door type, size and swing direction noted.
  • Any hardware or doors you have bought, unopened.
  • Clear space around each door.
  • Notes on drafts, light gaps or moisture.
  • Details of building rules for condos and apartments.

Anatomy of a door: the parts that matter

A door is more than a slab. It is a system of parts that must work together. Knowing the names helps when describing a problem.

  • Slab. The door itself.
  • Jamb. The frame the door sits in. Side jambs, a head jamb at the top and, on exterior doors, a threshold at the bottom.
  • Casing. The trim around the jamb on both sides, covering the gap between the frame and the wall.
  • Stop. The strip against which the door closes.
  • Hinges. Usually two or three, attached to the door edge and the jamb.
  • Latch and strike plate. The latch bolt in the door edge catches in the strike plate on the jamb.
  • Handle or knob, and lockset. The hardware operating the latch and locking the door.
  • Weatherstripping, sweep and threshold. On exterior doors, the seals that keep out air, water and pests.
  • Reveal. The gap between the door and the jamb, ideally even all around.

Choosing an interior door

Panel (traditional) doors

Doors with raised or flat panels in a frame, in styles from two-panel to six-panel and more. They suit traditional and transitional homes, and they come in solid wood and engineered versions.

Flush doors

Smooth, flat doors, hollow or solid core, for a clean, modern look. Hollow-core flush doors are light and economical, and solid-core flush doors are heavier, quieter and feel more substantial.

Shaker and contemporary doors

Simple, framed designs that suit a wide range of homes, popular in current styles.

Glass and French doors

Doors with glass panels bring light between rooms. Safety glazing may be required, and privacy glass options exist.

Barn doors and sliding doors

Hung on a track that runs along the wall, saving swing space. They need solid wall backing and clearance, and they offer less sound and privacy than hinged doors.

Pocket doors

Slide into a cavity inside the wall. They save space, but installation is more involved, and repairs may need access to the wall cavity.

Bi-fold and bypass doors

Common for closets. Bi-folds fold in half on a track, and bypass doors slide past each other. They need accurate track installation and alignment.

Material and core

  • Hollow-core. A thin skin over a honeycomb or frame. Light, economical and less sound-resistant.
  • Solid-core. A dense composite core. Heavier, better for sound and a feeling of quality.
  • Solid wood. Strong and attractive, but prone to seasonal movement and heavier.
  • MDF and moulded doors. Smooth for painting, stable and available in many designs.

Choosing an exterior door

Exterior doors affect security, comfort and appearance. The main choices are:

  • Steel doors. Strong and economical, with an insulated core. They can dent and rust if the surface is damaged.
  • Fibreglass doors. Durable, low-maintenance and insulated, with wood-grain options. They resist swelling and rot.
  • Solid wood doors. Beautiful and repairable, but needing finishing and maintenance, and they respond to moisture.
  • Glass and sidelights. Add light, with attention to energy performance and security.

Consider insulation value, the quality of the weatherstripping, the frame, the lock and the finish. A good door in a poor frame will not perform, and a good installation matters as much as the door.

Prehung versus slab: choosing the method

When replacing a door, the choice is between replacing only the door or the whole unit.

  • Replace the slab only when the frame is in good condition, square and the right size. Hinge and latch locations must be machined to match.
  • Replace the whole prehung unit when the frame is damaged, out of square or the size is changing. This is more work, but usually gives the best result.

Step by step: diagnosing a sticking door

  1. Close the door and look at the reveal on all sides.
  2. Find the rub. Slide a thin card or paper around the edge to find tight spots, and look for shiny or scraped areas.
  3. Check the hinges. Tighten the screws and look for loose or bent hinges.
  4. Check the frame. Is it square? Has it moved? Are there cracks?
  5. Consider the season. If the door sticks only in humid months, seasonal swelling may be the cause.
  6. Choose the fix. Adjusting hinges, shimming, sanding or planing, in that order.
  7. Seal any cut edge with paint or sealer.

Step by step: hanging a new interior door

  1. Measure the rough opening, checking that it is plumb, level and square.
  2. Remove the old door and frame if needed, and prepare the opening.
  3. Test fit the prehung unit, and check the hinge side is plumb.
  4. Shim and fasten the hinge side, using a level and fastening through the shims.
  5. Check the swing and reveal, then shim and fasten the latch side and the head.
  6. Trim excess shims and install the stops and casing.
  7. Install the hardware, bore the latch holes if needed and fit the strike plate.
  8. Fill, caulk and paint.
  9. Test the door through its full swing, and adjust if needed.

Exterior doors: weatherstripping and threshold in detail

  • Compression weatherstripping. Foam or rubber strips pressed between the door and the frame. They compress over time and need replacing.
  • Kerf-in weatherstripping. Fits into a groove in the jamb, common on newer doors, and can be replaced as a unit.
  • Door sweeps and bottom seals. Close the gap at the bottom of the door, and wear out where the door drags.
  • Adjustable thresholds. Have a screw-adjusted cap to raise or lower the sealing surface, giving a tight seal and easier operation.
  • Frame and sill condition. Rotting sills and frames let water and cold in, and must be repaired before sealing will work.

A quick draft test: close the door on a thin strip of paper at different points around the frame. If it slides out easily, the seal is loose there.

Security: making a door harder to defeat

  • Deadbolt with a solid strike. The bolt should extend at least an inch into the frame.
  • Long screws in the strike and hinges. Screws that reach the framing, typically about 3 inches, resist forced entry.
  • Reinforced frame. Metal reinforcing plates or strike boxes strengthen weak jambs.
  • Solid door. A solid-core, steel or fibreglass door is stronger than hollow.
  • Peephole or doorbell camera. For seeing who is outside.
  • Smart locks and keypads. Offer convenience, with attention to power, backup keys and compatibility.
  • Patio doors. A bar or pin in the track and a secondary lock can improve security.

Security upgrades work best as a system. We can install the hardware and reinforcements, and for a deeper security assessment, a specialist can advise.

Doors and accessibility

Doors can be barriers for people with mobility limits. Considerations include door width, lever handles instead of knobs, thresholds that are low or flush, offset hinges that widen the opening and automatic or power-assisted openers. We can help assess a doorway and suggest improvements within our scope, and for structural widening, a larger project may be needed.

Bright kitchen with white cupboards and drawers
Well-adjusted cupboard doors and drawers close evenly and quietly.

Doors and energy efficiency

Exterior doors can account for noticeable heat loss when seals fail. Good weatherstripping, a tight threshold, an insulated door and a well-sealed frame all help. Storm doors add another layer, and some can be adjusted to allow ventilation. See also seasonal advice in our blog and our indoor and outdoor repair projects page for caulking and sealing.

Frequently asked questions in more detail

Can you change the direction a door swings?

Often, yes, by moving the hinges and re-cutting the latch locations, or by replacing the unit. It depends on the door, the frame and the space.

Can you cut a door shorter or narrower?

Doors can be trimmed within limits, set by the manufacturer. Hollow-core doors have limited material at the edges, and solid doors have more tolerance.

Can you paint or stain a new door?

Yes. Pre-finished doors are available, and unfinished doors can be painted or stained. Edges and ends should be sealed. See residential painting.

My door slams or swings on its own. Why?

Often the hinges are not plumb, or the frame leans. Adjusting hinges and shims usually cures it.

Do you install door closers and stops?

Yes. Closers, stops, and kick plates are standard installations.

How long does a door installation take?

A single interior door is typically a short visit, with extra time for trim, painting and any frame repair. Exterior doors take longer because of sealing and weatherproofing. We give an estimate with the quote.

Door hardware: choosing and fitting

Handles and knobs

Levers are easier to use for people with limited grip, and knobs are traditional. Interior doors use passage sets (no lock), privacy sets (push-button or turn lock, for bedrooms and bathrooms) and dummy sets (a handle with no latch, for closets and pairs of doors). The backset, the distance from the door edge to the centre of the hole, is usually standard, and the bore size and the latch type need to match.

Deadbolts and entry locks

Single-cylinder deadbolts have a key on the outside and a thumb turn inside. Double-cylinder deadbolts need a key on both sides, which can be a fire-safety concern, and may be restricted in some settings. Check that your hardware is suitable for the door’s thickness, and consider a matching handle set.

Hinges

Hinge size and weight rating matter. Heavy and solid doors need three hinges, and wide or tall doors may need more. Ball-bearing hinges handle heavy and frequently used doors. Finishes should match the other hardware. Replacement hinges need to match the size, the radius of the corners and the screw pattern of the old ones, or the mortises must be adjusted.

Door stops, closers and kick plates

Door stops protect walls. Closers keep doors closed, such as for garages and fire doors, and need adjusting for speed and latching. Kick plates protect the lower part of doors from damage.

Privacy, security and special locks

Bathroom and bedroom privacy locks, keyed locks for offices and storage rooms and smart locks all have different installation needs. We confirm the product’s compatibility with your door before installing.

Painting and finishing doors

A door that is finished properly lasts longer and looks better. Whether new or repaired, doors benefit from a careful approach.

  1. Remove hardware or mask it carefully.
  2. Clean and sand the surface, to give paint something to grip.
  3. Fill and smooth dents and holes.
  4. Prime, including the top and bottom edges.
  5. Paint in thin coats, in the correct order for panel doors: panels first, then horizontal rails, then vertical stiles.
  6. Seal the top and bottom edges, which are the most vulnerable to moisture.
  7. Let it cure before closing, to avoid sticking.

Exterior doors need paint or stain rated for exterior use, and sun-facing doors need extra care, since dark colours heat up and can warp some doors. Check the manufacturer’s guidance on colour. See residential painting for painting services.

Doors in rental properties and multi-unit buildings

Doors take a lot of wear in rentals. Turnover work often includes replacing damaged hollow-core doors, repairing holes, re-keying or replacing locks between tenants and checking that fire-rated doors are in good order. Fire doors and their closers, seals and hardware are part of a building’s life safety, and they should not be altered without checking requirements. We can quote repairs across multiple units, with consistent hardware to simplify future maintenance.

Seasonal door care in Ontario

Doors respond to the seasons. A little attention at the right time keeps them working and sealing well.

  • Spring. After winter, check weatherstripping, thresholds and the bottom of exterior doors for water damage. Lubricate hinges and locks, and clean away salt residue.
  • Summer. High humidity swells wood doors. Make sure edges and the top and bottom are sealed, and avoid forcing a sticking door, since the problem may ease when conditions change.
  • Fall. Replace worn weatherstripping and sweeps before cold weather, adjust thresholds and check that locks and latches work smoothly.
  • Winter. Cold can contract frames and stiffen seals. Keep the threshold clear of ice and snow, and do not pour hot water on frozen locks. A little graphite or lock-specific lubricant helps.

Door installation checklist

  • Opening measured for width, height and wall thickness.
  • Swing direction and hinge side decided.
  • Door type chosen: prehung or slab, hollow or solid.
  • Hardware chosen, with backset and bore sizes confirmed.
  • Floor height and any new flooring considered.
  • Casing and trim style matched to the room.
  • Paint or stain planned, with edges sealed.
  • Fire rating or building rules checked for entry and garage doors.

Doors, noise and privacy

Doors are the main route for sound between rooms. Hollow-core doors let a great deal through, while solid-core doors with good seals reduce it noticeably. Gaps matter as much as mass: a large gap at the bottom of a bedroom or office door lets sound and light leak, and a simple door bottom or perimeter seal can help. Privacy hardware, thicker doors and sealing the frame improve things further. If sound is a concern in your home, tell us which rooms matter most, and we suggest practical options that suit your doors and budget.

Official guidance: For independent consumer information in Ontario, see Consumer Protection Ontario.

Door installation and repair in London, Ontario

Send us your list and a few photos. We will tell you what is involved and give you a clear written estimate. You can call 519-494-3673, message us on WhatsApp or use the contact form for a free consultation. For other small jobs, see general handyman repairs.

Before we start

A little preparation makes door installation and repair go more smoothly. Photos, rough measurements and a list of what you want done. If you already own the item being installed, keep its box and hardware.

Serving London, Ontario

We work with homeowners, landlords and businesses across London, Ontario and the surrounding area. Call 519-494-3673 or request a free consultation. You can also browse all of our services or see more handyman services work.

Frequently asked questions

How much does door installation and repair cost in London, Ontario?

Handyman work is usually quoted by the job or by the hour, depending on how clear the scope is. Small, well-defined tasks are easiest to price from a few photos; a list of several jobs is best quoted together. Call 519-494-3673 or send a message for an estimate for your address.

How long does door installation and repair take?

Most handyman tasks fit in one visit, and a short list of jobs often fits in a day. Anything that needs materials to be ordered or paint to cure is scheduled in two steps.

What should I have ready before booking door installation and repair?

Photos, rough measurements and a list of what you want done. If you already own the item being installed, keep its box and hardware.

What should I know about door installation and repair before we start?

Drafty exterior doors often need new weatherstripping or a threshold adjustment, not a full replacement.

Can you install a new interior door?

Yes. We hang prehung and slab doors, trim them to fit, install the hinges and hardware, adjust the gaps and finish the edges. Tell us the opening size, swing direction and door type, and we will confirm what is needed.

Why does my exterior door let in drafts?

Usually worn weatherstripping, a threshold set too high, a door that has shifted or gaps around the frame. Many drafty doors can be fixed with new weatherstripping and adjustments, not a replacement.

Can you repair a door that sticks or sags?

Yes. We check the hinges, the frame and the fit, then adjust, fasten or trim as needed. Sealing any cut edge protects the wood from moisture afterwards.

Can you replace locks and deadbolts?

We install and replace door hardware, including handles, locks and deadbolts, and adjust latches and strike plates. For high-security or smart-lock needs, tell us the product, and we will confirm that it fits.

Do you install storm doors or patio doors?

Tell us the type of door and the opening. We will confirm what we can do and, if a job needs a specialist installer or a structural change, we say so honestly.

Last updated

Free consultation

Tell us what you need and get a clear, written estimate.

Ready to start your project?

Book a free consultation. Tell us what you need and we will get back to you with clear next steps.